-
Supermirror Guide testing
This dataset has no description
-
Color reflectance, oxides and calcium carbonate analysis from the Attefeld lo...
This dataset has no description
-
Color reflectance from the Talheim loess-paleosol sequence in the Heilbronn B...
This dataset has no description
-
Color reflectance from the Frankenbach loess-paleosol sequence in the Heilbro...
This dataset has no description
-
Extracted color reflectance profile data of ODP Hole 177-1088B
Composite core images for Ocean Drilling Program (ODP) Hole 1088B were generated by cutting individual core sections from core table photos (downloaded from JANUS:... -
Color reflectance and oxide concetrations of loess-paleosol sequence Zilly
This dataset has no description
-
Color reflectance and oxide concetrations of loess-paleosol sequence Hecklingen
This dataset has no description
-
Underway CH4 measurements during POSEIDON cruise POS348
Coastal upwelling regions have been identified as sites of enhanced CH4 emissions to the atmosphere. The coastal upwelling area off Mauritania (NW Africa) is one of the most... -
(Table 6) Carbon and oxygen content and gas-hydrate saturation of ODP Leg 164...
Sediment depth is given in mbsf. Processed C/O ratio values can be found in Table 3 (doi:10.1594/PANGAEA.804157). -
(Table 5) Volume of natural gas within the downhole log-inferred free-gas occ...
Sediment depth is given in mbsf. Volume of in-place gas at in situ pressure and temperature conditions (pressure = 101 kPa, temperature = 15ºC). -
(Table 4) Volume of natural gas within the downhole log-inferred gas-hydrate ...
Sediment depth is given in mbsf. Gas volume calculation assumes a hydrate number of 6.325 (90% gas-filled clathrate), 1 m3 of gas hydrate = 164 m3 free gas at in situ... -
(Table T4) Vertical permeability measurements of ODP Site 180-1109
This dataset has no description
-
(Figure 5b) Vertical sensor characteristics of GEM-3 (96 cm coil) for quadrat...
The models are based on 0.1% perturbations of an homogenous seafloor model with seawater (and sediment) conductivities/susceptibilities of 3 S/m and -9 x 10-6 (1 S/m and 100 x... -
(Figure 5a) Vertical sensor characteristics of GEM-3 (96 cm coil) for in-phas...
The models are based on 0.1% perturbations of an homogenous seafloor model with seawater (and sediment) conductivities/susceptibilities of 3 S/m and -9 x 10-6 (1 S/m and 100 x... -
(Table T37) Ko-consolidated undrained test conditions and properties of undra...
All stresses / pressures were originally measured in ksc (kgf/cm**2). The conversion of ksc to SI units is 1 ksc = 98.07 kPa. -
(Table T36) Ko-consolidated undrained test conditions and consolidation prope...
All stresses / pressures were originally measured in ksc (kgf/cm**2). The conversion of ksc to SI units is 1 ksc = 98.07 kPa. Test samples TX641, TX644, TX647 and TX650 were... -
(Table T17) Constant rate of strain consolidation test conditions and consoli...
All stresses / pressures were originally measured in ksc (kgf/cm**2). The conversion of ksc to SI units is 1 ksc = 98.07 kPa. Test samples CRS499 and CRS577 were omitted because... -
Lightness data extracted from core images of sediment core GeoB24011-1
Field data: Lightness data extracted from core images of gravity corer sediments collected during project Kerguelen Plateau Sediment Drifts with RV Sonne Cruise SO272 in... -
Lightness data extracted from core images of sediment core GeoB24010-1
Field data: Lightness data extracted from core images of gravity corer sediments collected during project Kerguelen Plateau Sediment Drifts with RV Sonne Cruise SO272 in... -
Lightness data extracted from core images of sediment core GeoB24009-1
Field data: Lightness data extracted from core images of gravity corer sediments collected during project Kerguelen Plateau Sediment Drifts with RV Sonne Cruise SO272 in...